How to Draw a Site Plan in Chief Architect

The information in this commodity applies to:

QUESTION

I would similar to know how to create a plot plan in Primary Architect. How is this accomplished?

Answer

A plot plan is substantially a map of a belongings'due south legal clarification. This article describes how to create an accurate plot plan by inputting lines, arcs and setbacks using the CAD tools available in Principal Architect.

• Creating a plot plan polyline
• Correcting an mistake
• Creating a curved belongings line
• Displaying line length, angle, and arc radius information
  
• Creating setback lines
• Accurately positioning a building
  
• Converting a plot programme to a terrain perimeter
  

To create a plot program polyline

1. Select CAD> Points> Input Point from the carte to open the New CAD Betoken dialog.
2. Select Accented Location, define the point's position at (0,0) for the Ten Position and Y Position, and so click OK.

   This is the current point and will serve as the Showtime Signal for the first line of the plot programme.

   

3. From the menu, select CAD> Lines> North Pointer , so click and elevate the line upward to create a Due north Pointer pointing upwards to the top of the screen.
4. Select CAD> Lines> Input Line to open the New CAD Line dialog one time again. Notice that the Start Point is (0,0), which is the location of the current signal that yous but created. Click the Number Fashion push at the bottom of the dialog and in the Dialog Number/Angle Mode dialog:
   
   
   • Select Decimal Anxiety for the Number Style.
   • Cull the Bending Style that matches your data, such as Quadrant Bearing or Azimuth Bearing.
   • Click OK.
     
5. Staying in the New CAD Line dialog, select the Relative to Offset Point choice and check Polar. Enter the length of the first side of your holding purlieus's legal clarification in the Distance field, and the angle of that line in the Angle field.

   

6. Click Next and enter the Altitude and Angle of the next property line.

   The adjacent belongings line volition be the one adjoining the end point of your outset line, rather than the kickoff point.

   

   Note: With the North Pointer pointing in the upwardly direction, an angle of 90 degrees volition travel in the direction of left to right, 0 degrees will become from bottom to meridian, 270 degrees will become from right to left, while 180 degrees will travel from acme to bottom.

   
   
7. Continue until all property lines are entered, and then click OK to close the dialog.

   The property line created should exist closed, with the terminate-point of the last line being the same as the get-go signal of the kickoff line.

   

   If you have received plot program information from a surveyor, keep in heed that whatsoever given line tin be described in two ways using Quadrant Bearings, and not all surveyors will describe the lines of a given plot in the aforementioned direction (ie, clockwise or counterclockwise).

   If the lines are not described in the same direction, and so your consequence will non be a closed polyline.

   
   

To correct an error

1. If a line is entered incorrectly, click OK to close the New CAD Line dialog.
2. Click on the wrong line to select it, then click on the Disconnect Selected Border edit button.
3. With the incorrect line now separate from the rest of the polyline, information technology tin now be deleted. Select the Delete edit button or the Delete primal on your keyboard.
4. Place a CAD point at the cease of the last correct line using the Place Signal tool to create a new current point.
5. Select the Input Line tool and go along entering data in the New CAD Line dialog as described in the section above.

To create a curved property line

1. Click on an existing property line to select it, and so click the Change Line/Arc edit button to turn this line into an arc.
2. If necessary, use the triangular reshape edit handle to make the arc concave or convex.
3. Click the Open Object edit button to open up the Polyline Specification dialog.
4. On the Selected Arc panel, click the Chord radio button under the Lock category, specify the length of the Radius, then click OK.

   In this case, a value of 65' is specified.
   
   

   A curved belongings line tin can too be created by entering data in the New Arc dialog. See the Chief Architect Reference Transmission for more information.

To display line length, bending, and arc radius data

1. Select Edit> Default Settings from the menu, expand the CAD category, select Full general CAD, then click the Edit button.
2. In the CAD Defaults dialog:

   

   • Choose the bending display method that matches your data under the Display Line Angle as section.
   • Click on the Ascertain button nether Displayed Line Length Format Preview to brandish the Displayed Line Length dialog, and nether Accuracy, select the Decimal Places radio push

     

   • Click OK and/or Washed on all dialogs to confirm the changes.
     
3. Click on the plot plan polyline to select it and click the Open up Object edit push button.
4. On the Line Style panel of the Polyline Specification dialog:

   

   • If you're using the Plot Program Saved Programme View, the plot programme may already be on the CAD, Plot Program layer.

     If y'all're not using the Plot Program Saved Plan View, modify the layer to CAD, Plot Plan, click the Define button adjacent to the Layer drop-down, and ensure that the CAD, Plot Plan layer is set to be displayed.

     For more information on layers and layer sets, please see the Related Manufactures section below.

   • Cheque Bear witness Length, Show Angle and All Angles.
   • Click OK to close the dialog and utilise your changes.
     

To create setback lines

1. Select Edit> Preferences if you lot're on a Windows PC or Chief Architect> Preferences if you're on a Mac, and on the Behaviors panel of the Preferences dialog:

   

   • Select the Concentric radio button under Edit Type.
   • In the Jump field, type in the setback distance required by your local planning section
   • Click OK to close the dialog and use your changes.
     
2. Click on the plot plan polyline to select it, and then click the Copy/Paste edit push.
3. Identify your cursor over a corner edit handle, then click and elevate towards the eye of the polyline. When a 2d, inner polyline displays, release the mouse.

   

4. Select the inner polyline and click the Open Object edit push.
5. On the Line Style console of the Polyline Specification dialog:

   

   • Click the Define push next to the Layer drop-downwardly and in the Layer Display Options dialog that displays, click the Copy push to re-create the layer, and change the proper name of the newly created layer to CAD, Setback.
   • Alter the Line Mode to a dashed line style.
   • Uncheck the Evidence Length and Show Bending boxes, if desired.
   • Click OK to shut the dialog and apply your changes.
     
   
6. Once the setback is created, navigate to Edit> Edit Behaviors and select the Default pick to switch back to the default edit behavior.

To accurately position a edifice

1. Navigate to CAD> Points> Place Point and place a point along the perimeter of the belongings, such as a corner. Alternately, use the starting point for your plot plan polyline, (0,0), as a reference.

   

2. Select CAD> Points> Input Indicate to open up the New CAD Point dialog.
3. Select Accented Location and specify the desired distance that the building volition be from this betoken in the X Position and Y Position fields.
4. If you have placed a CAD point at a dissimilar location, select Relative to Electric current Point and specify the desired distance from that point. Unless you would like to specify the location in distance and bearing, Polar (CCW from horz) should remain unchecked.
5. When you click OK, a point will be created at the specified location. Use this point every bit a reference to accurately position a wall or corner of the building.

To convert a plot programme to a terrain perimeter

If you'd like to accept your Plot Programme appear in 3D views as a grass pad with a thickness, you can convert information technology to a Terrain Perimeter.

1. Select the plot plan polyline and click the Catechumen Polyline edit push.
2. In the Catechumen Polyline dialog, select Terrain Perimeter, specify the Layer you would similar the Terrain Perimeter to go on, then click OK.
   
   
3. Brand whatsoever needed changes, then click OK to close the dialog.

   The plot plan polyline that you created is now your Terrain Perimeter.

havemaneattelf.blogspot.com

Source: https://www.chiefarchitect.com/support/article/KB-00575/creating-a-plot-plan.html

Share this post